3D Printer Machines
Stainless Steel Barrel for MK8 Extruder
$19.00
Now:
$15.00
1. This is a barrel for both single and dual MK8 extruder with a PTFE tube inside (Note:3mm model has no PTFE tube inside). 2. Please note that the 1.75mm MK8 extruder is not compatible with the 3mm one, and you can not convert your 1.75mm extruder into...
Nema 17, 42 BYG Shaft-reversed Stepper Motor
$30.00
Now:
$23.00
1. This is a shaft- reversed stepper motor that is frequently used in CNC machines and 3D printers. 2. The Advantages of step motors are low cost, high reliability, high torque at low speeds and a simple, rugged construction that operates in almost any...
MK8 Assembled Extruder
$53.00
Now:
$41.00
1. 42mm high quality stepper motor with larger torque and less heat build up. 2. Special ceramic insulation cotton ensures the stability of heating; electricity-saving. 3. Direct transmission, without the heavy gears, compact size and weight. 4. Material...
MK2a Heated Bed Prusa Soldered Resistor & LED for Reprap, Mendel
$21.00
Now:
$17.00
1. Please use a good power supply and thick copper wire to connect the heat bed. 2. You need basic soldering skills to solder the power wire.
MK8 Dual Extruder
$109.00
Now:
$85.00
1. This is a dual extruder which can be used on 3D printers like Mendel, Prusa, Makerbot, and Printrboard and others. 2. The two print heads are conjoined with a piece of high hardness aluminum bar with good heat dispersion and high reliability. 3. The...
3D Printer LCD Panel Adapter for RAMPS-FD
$20.00
Now:
$15.00
1. LCD-Panel-adapter-FD is an adapter for Adruino DUE and Ramps-FD, which are always combined to work as a 3D printer control board. 2. As the operating voltage of the Arduino DUE chip is 3.3v, while the LCD display works best at 5V, we add a signal...
MK8 Extruder Aluminum & Stainless Steel & Brass Materials Hot End kit
$18.00
Now:
$14.00
1. Material: Aluminum & Stainless Steel & Brass. 2. Connection method: external thread connection. 3. Scope of application: 3D printer. 4. Operating temperature range: -40 degree to +300 degree. 5. Cartridge Heater: 12V 40W.
3D Printer Smart Adapter for LCD Panel of Ramps 1.4
$26.00
Now:
$20.00
1. This adapter is for RAMPS 1.4 Smart Controller LCD 2004 & LCD 12864. 2. You can easy connect it to your RAMPS1.4 shield using this smart adapter. 3. After connecting the panel to your RAMPS1.4 shield you can print your 3D designs without PC, just...
1m Rubber 2GT Timing Belt
$32.00
Now:
$25.00
1.The 2GT Timing belt will work better than T5, T2.5, it gives better smoothness and accuracy of positioning. 2. It is especially suited for linear movement and positioning applications. 3. Adopt high quality rubber materials, sturdy and durable.
MK8 Extruder Aluminum Feeder Kit for 1.75mm / 3mm Filament
$28.00
Now:
$22.00
1. This is an MK8 Extruder Aluminum feeder Kit for 1.75mm /3mm filament. (3mm is only available for short distance ). 2. This kit is also available for both left and right hand direction, short-distance and long distance(with two push-in fittings),...
Geeetech 3D Touch Automatic Bed Leveling Sensor for 3D Printer
$72.00
Now:
$56.00
1. The product can precisely measure the tilt of your print surface. It can greatly improve the printing precision of your 3D Printer. 2. 3D Touch features simple, smart and precise. It could work with nearly any kind of bed materials, such as glasses,...
DRV8825 Stepper Motor Driver Carrier Reprap 4 Layer PCB
$25.00
Now:
$19.00
1. The DRV8825 stepper motor driver carrier is a breakout board for TI DRV8825 microstepping bipolar stepper motor driver. 2. Simple step and direction control interface. 3. Six different step resolutions: full-step, half-step, 1/4-step, 1/8-step,...
Mechanical End Stop Switch Module V1.2
$16.00
Now:
$12.00
1. The mechanical endstop uses a lever switch to detect when it is activated. 2. The switch is wired up so that when activated, it pulls the signal to LOW. 3. There is also an LED on the board that will light up when the switch is activated. It uses a...
GT2560 3D Printer Controller Board
$83.00
Now:
$65.00
1. The firmware is the prevalent Marlin, which is known for its stability, usability, and high-performance. 2. Adopt ATmega2560 as the main control chip, coupled with the high-performance USB serial converter FT232RQ. 3. The power pack: operating...
New MK8 Extruder
$60.00
Now:
$46.00
1. This is an modified MK8 extruder, which features outstanding quality and ensures better performance for 3D printers. 2. The heat-resisting PTFE tube inside the barrel ensures fluent feeding and helps avoid blocking problem thanks to its self-lubricity...
10 PCS 3D J-Head Hotend / E3D Extruder Nozzle Drill Cleaner
$21.00
Now:
$16.00
1. These extruder nozzle drill cleaners are powerful tools that any 3D printer owner must have. 2. The drills are made of Tungsten steel, hard and thin enough to get into the nozzle and extract the blocked filament. 3. There are 4 types of drills of 0...
10m 1.75mm Normal Temperature PLA Cable 3D Printing Pen Consumables(Yellow Gold)
$27.00
Now:
$21.00
1. Product name: 3D printing pen consumables 2. Specification: 1.75mm 3. PLA printing temperature: 160-230 degrees 4. Purpose: DIY creation, printing and painting 5. Material: PLA
5m 1.75mm Low Temperature PCL Cable 3D Printing Pen Consumables(Black)
$27.00
Now:
$21.00
1. Product name: 3D printing pen consumables 2. Specification: 1.75mm 3. PCL printing temperature: 10-100 degrees 4. Purpose: DIY creation, printing and painting 5. Material: PCL
5m 1.75mm Low Temperature PCL Cable 3D Printing Pen Consumables(Light Red)
$27.00
Now:
$21.00
1. Product name: 3D printing pen consumables 2. Specification: 1.75mm 3. PCL printing temperature: 10-100 degrees 4. Purpose: DIY creation, printing and painting 5. Material: PCL
10m 1.75mm Normal Temperature PLA Cable 3D Printing Pen Consumables(Brown)
$27.00
Now:
$21.00
1. Product name: 3D printing pen consumables 2. Specification: 1.75mm 3. PLA printing temperature: 160-230 degrees 4. Purpose: DIY creation, printing and painting 5. Material: PLA